The main products of Jichai 190 are: 6190 accessories, 8190 accessories, 12V190 accessories, Jichai H16V190 accessories, gas engine accessories, biogas generator set accessories, gas engine accessories, ship engine accessories. Supply 190 accessories, body, crankshaft, 12VB.03.00 diesel engine cylinder head assembly, gas engine cylinder head assembly, 16V gas engine cylinder head assembly, 190 connecting rod assembly, connecting rod shingle, thrust shingle, thrust plate, Z12VB.05.01C piston, 190 cylinder liner, supercharger (20GJ supercharger,SJ160 supercharger, J170 supercharger) intercooler, 12VB.22.00B water pump, Diesel overhaul package, whole car cushion, 190 camshaft, gas motor, electric starting motor, 3411 high spring coupling, Changsha Zhengsheng piston ring group, 190 inlet and exhaust valve and seat ring, three-core speed sensor, instrument panel, STITT spark plug, ignition coil, 127.90.10 high voltage wire, ignition controller, 190 oil filter, 190 accessories, 12VB.21.00 oil cooler, high pressure oil pump, governor, centrifugal filter, Cheshire oil filter, Cheshire 12V190 accessories, Cheshire air filter, Cheshire three filters, Cheshire combination narrow V belt, Cheshire fuel injector, Jichai ZCK150S835 nozzle couple,ZCK150S840 nozzle couple, 12V.29.00 hand pump, 307.54.00 electric pre-supply pump, sea water pump, Jichai coupling accessories.
12V190 Maintenance tool, cylinder liner pickpocket, Valve Seat ring disassembly tool, valve guide disassembly tool, piston ring disassembly tool, valve seat reamer, torque wrench, 190 valve spring disassembly tool.
When the diesel engine is used for a certain period of time, or when it is dismantled and inspected, the relative installation position and transmission relationship of some parts will change, which will affect the service performance of the diesel engine. Therefore, in the process of diesel engine use, it is necessary to check and adjust some main parameters (such as gas "gap, gas distribution timing, oil supply advance Angle, injection pressure, etc.) to ensure that the diesel engine works reliably and the performance is stable
Be sure. In order to obtain accurate inspection and adjustment results, the relative position of the flywheel scale and pointer should be checked before operation, that is, when the diesel-cylinder piston is located at the top dead center position, the pointer should be exactly indicated at the "0" position of the flywheel scale. Diesel engine factory, pointer indicating position has been adjusted well fixed, in use should pay attention to protect, prevent bump or distortion. If the pointer is damaged or the indicating direction is changed, it should be repaired and adjusted. Yes: The pointer is fixed on the body, so that the indicating arrow points to the flywheel scale. Remove the fuel injector from cylinder (or sixth cylinder). Take an 814x220mm steel bar (both ends should be flat) and insert it straight into the cylinder from the injector seat hole. The disc turning crankshaft places the cylinder piston near top dead center. A dial gauge is fixed on the cylinder head so that its contacts are pressed against the end face of the steel bar. The disc turns the crankshaft and the steel rod is pushed up by the piston while the dial indicator increases. Drive the crankshaft to a - position and record the reading of the dial meter at this position (assume 1mm) and the pointer indicating the scale on the flywheel (assume 354"). Continue to turn the crankshaft, so that the steel bar crank up to down, dial value from increase to decrease. When the dial indicator returns the original value (Imm), its corresponding pointer indicating scale (0%), at this time, the average value of the two calibration indicating values (354*+360*) + 2=3579, that is, the zero value at the top dead center of the piston. The crank shaft is rotated so that the pointer points to the average scale (357") position, and then the flywheel position is fixed, the pointer indication is moved to "0" position, and the pointer is fixed.
Shandong Hongfan Power Technology Co., Ltd. to provide you with Ji Chai accessories, Sheng moving accessories, Zi Chai 8300 accessories. Our company produces Ji Chai 190 accessories, Sheng Dong 190 accessories, Zi Chai 8300 accessories, Zi Chai 6300 accessories, Zi Chai 6170 accessories, Zi Chai 8170 accessories, accessories,
Accessories are suitable for all types of Jichai generator set, Shengdong gas generator set, Zichai 8300 biomass gas generator set, etc.
Audited Supplier 
){kind=link}
){kind=link}